First Alert Fa 1600 Programming Manual
ModePress these KeysStay – HomeYour Code + STAY (3)Night Stay – HomeYour Code + STAY (3) + STAY (3)Instant – HomeYour Code + INSTANT (7)AwayYour Code + AWAY (2)MaximumYour Code + MAX (4)Door Chime ON/OFFYour Code + CHIME (9)Off/DisarmYour Code + 1Common Security Alarm Problems and Questions for the FA260Here are some helpful answers to some basic questions you may have about the First Alert FA260 Keypad. How to Change the Home Alarm CodeThere may come a time where you need to know how to reset the home security alarm code. If you need to change security alarm codes, you will require the Master Code. This will usually be written somewhere in your documentation, such as in the owner’s manual or a card your technician provides.Press either the Reset button or No. 9 on the keypad. When you hear three beeps, enter your current alarm code and the pound sign, followed by the Master Code. This should give you a prompt wherein you can enter your new security code.
Be sure to choose a code you have not used before.If you cannot find the Master Code, you can set one with your Installer Code. Type in the Installer Code, then 802 and your new four-digit Master Code. A short beep should indicate you have successfully made the change and you can proceed as above to change the alarm code. How to Change the Battery on the FA260To change the battery on the FA260, you will want to first use your code to silence the alarm. If you see a Bat sign to indicate there is a low battery, you will need to change it. Find the can where your alarm’s wiring is contained. Your technician should have shown you where it is when he installed the system, but it is often in a basement or other out-of-the-way area.
In some situations, it could be directly underneath the keypad.Once you find it, open it up. You should find the battery fairly easily — it will usually be in the corner connected to a red-and-black wire. Simply remove the wires from the connections on top of the battery, one at a time. Take your new battery and simply reattached the connections, making sure the red wire connects to the red-labeled connector and the black wire connects to the black-labeled connector.Once the battery is connected, re-enter your code to clear the low battery signal and you should be able to use your keypad normally.
If your battery signal does not go away, contact Wayne Alarm Systems for additional assistance. Why Should You Upgrade Your Security Alarm?If you have not upgraded your security alarm in some time, you may not be aware that there are many benefits to having a. The most important is that older security systems are dramatically easier to hack than new ones. Old systems rely on phone lines, which means all the intruder has to do is cut them to disable your system.
Today’s systems work wirelessly and continue to work even if Wi-Fi is down or there is a power outage, so you are always protected.Additionally, you can control wireless security alarms through an app on your phone, so you can turn it on and off remotely and receive alerts whenever the system is tripped, no matter where you are. You are always tuned into what is happening in and around your home.Furthermore, you can hook your modern security system into other necessary home monitoring systems, like, for complete home protection.
First Alert Fa 1600 Programming Manual 2017
TO ENTER PROGRAMMING MODE:Local programming requires the use of an alpha keypad connected to the keypad terminals on the control.A. POWER UP, then depress and # both at once, within 50 seconds of powering up (if 98 was used to exit program mode, this method must be used to reenter program mode).ORB. Initially, key: Installer Code (4 + 1 + 1 + 2) plus 8 + 0 + 0.DATA FIELD PROGRAMMING PROCEDURESTaskProcedureGo to a Data FieldPress + Field Number, followed by the required entry.Entering DataWhen the desired field number appears, simply make the required entry. When the last entry for afield is entered, the keypad beeps three times and automatically displays the next data field insequence.If the number of digits that you need to enter in a data field is less than the maximum digits available(for example, the phone number fields.41,.42), enter the desired data, then press to end theentry. The next data field number is displayed.Review a Data FieldPress # + Field Number.Data will be displayed for that field number. No changes will be accepted in this mode.Deleting an EntryPress + Field Number +.
(Applies only to fields 40 thru.46,.94, and pager programmingfields)INTERACTIVE MODE PROGRAMMING ( 56, 57, 58, 79, 80, 81, 82, 187)Press + Interactive Mode No. (for example, 56). The alpha display keypad will display the first of a series of prompts requesting entries.Interactive ModeUsed to Program56 Zone ProgrammingZone characteristics, report codes, alpha descriptors, and serial numbers for 5800 RFtransmitters.57 Function Key ProgrammingUnlabeled keypad keys (known as ABCD keys) for special functions58 Zone ProgrammingSame options as.56 mode, but with fewer prompts.
Intended for those familiar with(Expert mode)this type of programming, otherwise.56 mode is recommended.79Output Device MappingAssign module addresses and map individual relays/powerline carrier devices80Output Programming4229 or 4204 Relay modules, Powerline Carrier devices, or on-boardtriggers81Zone List ProgrammingZone Lists for relay/powerline carrier activation, chime zones, pager zones, etc.82Alpha ProgrammingZone alpha descriptorsINITIALIZE DOWNLOAD and RESET DEFAULTS96 Initializes download ID and subscriber account number. 97 Sets all data fields to original factory default values.TO EXIT PROGRAMMING MODE:98 Exits programming mode and prevents re-entryby: Installer Code + 8 + 0 + 0. If 98 is used to exit programming mode, system must be powered down, and method A above used to enter the programming mode.See field.88 for other.98 Program mode lockout options.99 Exits programming mode and allows re-entryby: Installer Code + 8 + 0 + 0 or method 1 above.Special MessagesOC = OPEN CIRCUIT (no communication between Keypad and Control).EE or ENTRY ERROR = ERROR (invalid field number entered; re-entervalid field number).After powering up, AC, dI (disabled) or Busy Standby and NOT READY will be displayed after approximately 4 seconds. This will revert to a “ Ready” message in approximately 1 minute, which allows PIRS, etc.
To stabilize. You can bypass this delay by pressing # + 0.If E4 or E8 appears, more zones than the expansion units can handle have been programmed. The display will clear after you correct the programming.
352.5$00,1. )250Entries apply to both the FA168CPS and FA148CP controls, except entries shown in dashed boxes, which apply only to the FA168CPS (partition entries) and are not applicable to the FA148CP.Entry of a number other than one specified will give unpredictable results. Values shown in brackets are factory defaults.FieldFunctionData EntriesProgrammable ValuesSYSTEM SETUP ( 20– 29)20INSTALLER CODE4 digits, 0–9 411221QUICK ARM ENABLE0,00 = no; 1 = yesPart. 1 Part.222RF JAM OPTION00 = no RF Jam detection; 1 = send RF Jam reportUL: must be 1 if wireless devices are used.
0 = no quick bypass UL: must be “0”1 = allow quick bypass (code + 6 + # )00 = disable all wireless keypad usage01–31= using 5827, 5827BD or 5804BD keypad 00,00,000 = no; 1 = yes (select zones to chime on zone list 3, using.81 Menu mode)0= A; 1 = B, 2 = C, 3 = D, 4 = E, 5 = F, 6 = G,7= H, 8 = I, 9= J, #10 = K, #11 = L, #12 = M, #13 = N,#14 = O, #15= PUL: not for fire or UL installations00 = disable; 1st digit: enter 1–9;2nd digit: enter # + 11 for ' ', or # + 12 for '#'.UL: must be “00” for UL Commercial Burg. Installations0 = disable; 1 = enable0 = no UL: must be “0”; 1 = yes0 = sounder stops at timeout;1 = no sounder timeout UL: must be “1” for fire install.0 = none; 1 = 4 min; 2 = 8 min; 3 =12 min; 4 = 16 min;UL: For residential fire alarm installation, must be set for a minimum of 4 min (option 1); for UL Commercial Burglary installations, must be minimum 16 min (option 4).
00 - 96 = 0 - 96 secs; 97 = 120 secsSIA Installations: minimum exit delay is 45 seconds UL: see inst. For requirements.Common zones use same delay as partition 1.00- 96 = 0 - 96 seconds97= 120 secondsSIA Installations:98= 180 secondsminimum entry delay is99= 240 seconds30 secondsFor UL Residential Burglary Alarm installations, must be set for a maximum of 30 seconds; entry delay plus dial delay should not exceed 1 min. For UL Commercial Burglar Alarm, total entry delay may not exceed 45 seconds.
DIALER PROGRAMMING ( 40 – 42)Do not fill unused spaces. Enter 0–9;#+11 for ' '; #+12 for '#'; #+13 for a 2-secondpause.
If fewer than the maximum digits entered, exit the field by pressing. The next data field number is displayed.40PABX ACCESS CODEEnter up to 6 digits. To clear entries, press 40. If call waiting used, enter “ (#+11) 70” plus “# + 13” (pause).41PRIMARY PHONE No.
42SECOND PHONE No. Enter up to 20 digits. To clear entries, press 41 or42 respectively.
Enter 4 or 10 digits, depending on selection in.48 Report Format. See box above.
To clear entries, press.43. FFFF Enter 4 or 10 digits, depending on selection in.48 Report Format. See box above. To clear entries, press.44. FFFF Enter 4 or 10 digits, depending on selection in.48 Report Format. See box above.
To clear entries, press.45. FFFF Enter 4 or 10 digits, depending on selection in.48 Report Format. See box above.
To clear entries, press.46. FFFFIf Cent. IS NOT on a WATS line: 0=Pulse; 1=Tone; if Cent. IS on a WATS line: 2 = Pulse; 3 = Tone0= 3+1, 4+1 ADEMCO L/S STANDARD1= 3+1, 4+1 RADIONICS STANDARD2= 4+2 ADEMCO L/S STANDARD3= 4+2 RADIONICS STANDARD5= 10-digitADEMCO CONTACT ID® REPORTING6= 4+2 ADEMCO EXPRESS7= 4-digitADEMCO CONTACT ID® REPORTING8= 3+1, 4+1 ADEMCO L/S EXPANDED9= 3+1, 4+1 RADIONICS EXPANDED0= Standard/backup reporting only (all to primary)Primary Phone No.2nd Phone No.1= Alarms, Restore, CancelOthers2= All except Open/Close, TestOpen/Close, Test3= Alarms, Restore, CancelAll4= All except Open/Close, TestAll5= AllAll. TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES ( 59 thru.68,.70 thru 76, and 89):For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9,#+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. A 0 ( not #+10) in the first box will disable a report. A 0 ( not #+10) in the second box will result in automatic advance to the next field.For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9,0, or B–F,as described above.A 0 ( not #+10) in the second box will eliminate the expanded message for that report.
A 0 ( not #+10) in both boxes will disable the report.For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the second boxes are ignored).A 0 ( not #+10) in the first box disables the report. UL: see installation instructions for requirementsSYSTEM STATUS REPORT CODES ( 59– 68)59 EXIT ERROR REPORT CODE0See box above.60 TROUBLE REPORT CODE00See box above. 61BYPASS REPORT CODESee box above. 0062AC LOSS REPORT CODESee box above.
0063LOW BAT REPORT CODESee box above. 0064TEST REPORT CODESee box above.
Use Scheduling mode to set periodic test reports, 00. 0 = no, 1 = partition 1 only2 = partition 2 only, 3 = both partitions0= 15 seconds6= 2-1/2min#+12 = 8 min1= 30 seconds7= 3 min#+13 = 10 min2= 45 seconds8= 4 min#+14 = 12 min3= 60 seconds9= 5 min#+15 = 15 min4= 90 seconds#+10 = 6 min5= 2 minutes#+11 = 7 min0= no, 1 = yes0= 15 seconds6= 2-1/2min#+12 = 8 min1= 30 seconds7= 3 min#+13 = 10 min2= 45 seconds8= 4 min#+14 = 12 min3= 60 seconds9= 5 min#+15 = 15 min4= 90 seconds#+10 = 6 min5= 2 minutes#+11 = 7 min. 160PAGER 1 PHONE No. Enter up to 20 digits. 0–9;#+11 = ' '; #+12 = '#'; #+13 = 2-secondpause.161PAGER 1 CHARACTERS Enter the optional prefix characters, up to 16 digits. 0–9;#+11 = ' '; #+12 = '#'; #+13 = 2-secondpause.162 PAGER 1 REPORT OPTIONS For each partition, select from the following options: 0 = no reports sent1 = Open/closes all users4 = All alarms and troubles5 = All alarms / troubles, and open/closes for all users 12 = Alarms / troubles for zones entered in zone list 9 13 = Alarms / troubles for zones entered in zone list 9,and open/closes for all users163 PAGER 2 PHONE No.
Enter up to 20 digits. 0–9;#+11 = ' '; #+12 = '#'; #+13= 2-secondpause. 166 PAGER 3 PHONE No. Enter up to 20 digits.
0–9;#+11 = ' '; #+12 = '#'; #+13 = 2-secondpause.167PAGER 3CHARACTERS Enter the optional prefix characters, up to 16 digits.0–9;#+11 = ' '; #+12 = '#'; #+13 = 2-secondpause.168PAGER 3 REPORT OPTIONS0,0,0See field.162 for reporting options. Select for eachPart. 2commonpartition (use zone list 11 if using options 12 or 13).169PAGER 4PHONE No. Enter up to 20 digits. 0–9;#+11 = ' '; #+12 = '#'; #+13 = 2-secondpause. Enter the desired 3-digitContact ID® report codes for alarms and troubles occurring on zones assigned to this zone type. Enter the codes sequentially (all 6 digits).
When entering digits, # moves cursor backmoves forward. Press when done to continue.Enter each touch screen (AUI) device’s home partition. 0 = disabled1 = partition 1; 2 = partition 2; 3 = partition 3 (common) NOTE: A minimum of one standard keypad must also be installed when AUI is used.
Use of AUI does not affect the number of standard keypads supported. KEYPAD OPTIONS.190-.196 ( NOTE: Options for keypad address 16 are set by the factory and cannot be changed.)NOTE: Each keypad must be assigned a unique address. Keypads programmed with the same address will give unpredictable results.190KEYPAD 2 DEVICE ADDRESS 170 0Partition:0 = keypad disabled; 1-3= part.
Configurable Zone Types WorksheetsConfigurable zone types 90 and 91 can be programmed via downloader software or from a keypad using data fields.182-.185.Configurable zone types 92 and 93 (FA168CPS only) can only be programmed using the downloader software.Programming Configurable Zone Type options involves making 10 entries in data field.182 for zone type 90 and field.184 for zone type 91, where each entry represents the sum of the values of the various options shown in the tables below. Use fields.183 and.185 to program Contact ID report codes for these zone types. ENTRY 1 (See note 5 for RF zones) ENTRY 2 (See note 5 for RF zones)Response when system disarmed and zone is:AutoIntact EOLOpenShortedRestoreVent ZoneRF zone normalRF zone N/ARF zn off-normal0= normal0= normal0= normal0 = no0 = no1= alarm4= alarm1= alarm4 = yes8 = yes2= trouble8= trouble2= trouble3= fault12 = fault3= faultEntry 1 = EOL + OpenEntry 2 = Short + auto restore + vent zoneENTRY 3 (See note 5 for RF zones)ENTRY 4 (See note 5 for RF zones)Response when armed STAY and zone is:Byp.
WhenIntact EOLOpenShorteddisarmedarmedRF zone normalRF zone N/ARF zn off-normal0= normal0= normal0= normal0 = no0 = no1= alarm4= alarm1= alarm4 = yes8 = yes2= trouble8= trouble2= trouble3= fault12 = fault3= faultEntry 3 = EOL + OpenEntry 4 = Short + byp. Disarmed + byp. Entries for Fields.182 and.184Entry Zone Type 90Zone Type 91(field.182)(field.18910To calculate the value for each entry:Simply add the values of the selected options in each of the entry’s columns (one option per column). For example, to program Entry 2 for “alarm response to short,” “auto restore on,” but not a “vent zone,” enter 5 (“1” for alarm short + “4” for auto restore yes + “0” for vent zone no).INTACTOPENSHORTEDEOLZONE-003-V0Zone Conditions Representedin Entries 1-6NOTES:1. Do not use the “fault delay” option with a configurable zone type if it is set for an entry or exit delay, otherwise unpredictable results may occur.2.
To create an interior type zone, select “respond as interior zone type” (entry 8, interior type = yes), and set zone response to “fault” in entries 3-4to ensure fault displays; do not set as “normal,” “alarm,” or “trouble.”3. Do not set fire zones to respond as a“fault” (entries 1-6),otherwise faults will not display unless the key is pressed.4. 4219/4229 modules must use EOLRs or unpredictable results may occur.5. RF Zones: The “open” option in entries 1, 3, and 5 is not applicable for RF zones. Use the “intact EOL” option for normal RF zone conditions and “shorted” for offnormal RF zone conditions.6. Zone-Doubling/Double-Balanced:A short on either zone of a zone-doubledpair or on a double-balancedzone causes a tamper condition.b.
For double-balancedzones, this entry must be “0.”c. For zone-doubledzones, both zones of the doubled pair must be assigned the same response to a short.57 FUNCTION KEY PROGRAMMINGOptionFunctionABCDComments01Paging02Time Display03Arm AWAY04Arm STAY05Arm NIGHT-STAY06Step Arming07Device ActivationDevice:08Comm. 80 OUTPUT DEFINITIONSFill in the required data on the worksheet below and follow the programming procedure in the installation manual as you enter the data during the displays and prompts that appear in sequence.Notes: 1. For Relays, 4229 and 4204 devices are programmed in.79,.80, and.81 modes.2. For Powerline Carrier devices (plcd), field 27 must be programmed with a House Code.
Note: Bulleted (.) words in boldface type are those that are also available for use by the FA4285/FA4286 Phone Module. If using a Phone module, and words other than these are selected for Alpha descriptors, the module will not provide annunciation of those words.Italicized words followed by an asterisk indicate those words supported by the FA560VKP Voice Keypad.CHARACTER (ASCII) CHART (For Adding Custom Words)32 (space)41)50259;68D77M86V071G80P89Y3?72H81Q90Z37%46.55764@73I82R5A74J7966B75K8:67C76L85U.
WIRELESS INPUT TYPES'RF' (Supervised RF) Type send periodic check-in signals, as well as fault, restore and low battery signals. The transmitter must remain within the receiver's range.“UR' (Unsupervised RF) Type send all the signals that the 'RF' Type does, but the control does not supervise the check-in signals. The transmitter may, therefore, be carried off-premises.'
BR' (Unsupervised Button RF) Type only send fault signals. They do not send restore or check-in signals. They will indicate a low battery condition when tested or activated normally. They can be carried off-premises.Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for details regarding loop numbers, etc.UL NOTE: The following transmitters are not intended for use in UL installations: 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, and 5850.The 5827BD and 5800TM can be used in UL Listed Residential Burglar installations. LOOP 3LOOPLOOP 2(REED)LOOP21(REED)(PRIMARY)LOOP 2LOOP 12LOOP 1(TERMINALS)(AUX. 24-HRBATTERY STANDBY REQUIRED FOR FIRE INSTALLATIONS. USE 12V, 17.2AH BATTERY FOR 600mA AUX POWER.
SEE INSTRUCTIONS.BATTERY CAPACITY FOR EMERGENCY BURGLARY STANDBY USE AT LEAST 4 HRSCHARGING VOLTAGE–13.8VDC. MAXIMUMBATTERYCHARGING CURRENT12V, 4AH +650mA.SEALED LEAD-ACIDTYPE. BATTERY NORMALLY NEED NOT BE REPLACED FOR AT LEAST 3 YRS.TO DETERMINE TOTAL STANDBY LOAD ON BATTERY, ADD 100mA TO TOTAL OF AUX. POWER OUTPUT AND REMOTE KEYPAD CURRENTS.USE UL LISTED LIMITED ENERGYCABLE FOR ALL CONNECTIONSCLASS 2 PLUG-INTRANSFORMER16.5VAC, 25VA (e.g. 1321).(USE No.
First Alert Fa1600c Programming Manual
1321CN IN CANADA)USE 4300 / 1321X10 TRANSFORMER INTERFACE IN PLACE OF 1321 OR 1321CN WHEN POWER LINE CARRIER DEVICES ARE BEING USED. (SEE INSTRUCTIONS FOR CONNECTIONS)THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIATION'S STANDARD 72, CHAPTER 2 (NATIONAL FIRE PROTECTION ASSOCIATION, BATTERY-MARCHPARK, QUINCY,MA 02269).PRINTED INFORMATION DESCRIBING PROPER INSTALLATION, OPERATION,TESTING, MAINTENANCE, EVACUATION PLANNING AND REPAIR SERVICE IS TO BE PROVIDED WITH THIS EQUIPMENT.CONNECTION OF THE FIRE ALARM SIGNAL TO A FIRE ALARM HEADQUARTERS OR A CENTRAL STATION SHALL BE PERMITTED ONLY WITH THE PERMISSION OF THE LOCAL AUTHORITY HAVING JURISDICTION. THE BURGLAR ALARM SIGNAL SHALL NOT BE CONNECTED TO A POLICE EMERGENCY NUMBER. 8-PINCONNECTOR42194-WIRESMOKE DETECTOR CONNECTIONSBATTERY FUSEUSED FOR 4300/1321X10+ 5FOR REPLACEMENT,TRANSFORMERADDITIONAL40TOUPFOR ZONESOREITHERFROM( BOTH GROUPS)WIRED EXPANSION MODULERED JUMPER17OUTPUT 1)(TRIG.AUX+12 GND18OUTPUT 2)(TRIG.TO TERM 5REDOPTIONALRED5881L: UP TO 83AUSE SAME VALUECONNECTIONS AND FOR(8 ADD'L EOLR WIRED ZONES)SET UNIT’SAUX PWRRELAY(e.g.